晚上才想起写一下，也是比较晚了。先把代码放上来。还有bug
各位好友尽请参考。
后面会给出详解
/* USER CODE BEGIN Header */
/**
******************************************************************************
* @file : main.c
* @brief : Main program body
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2021 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include "function.h"
#include "lcd.h"
#include "stdio.h"
#include "string.h"
/* USER CODE END Includes */
/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
/* USER CODE END PTD */
/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD */
/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */
/* USER CODE END PM */
/* Private variables ---------------------------------------------------------*/
TIM_HandleTypeDef htim3;
UART_HandleTypeDef huart1;
/* USER CODE BEGIN PV */
/* USER CODE END PV */
/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_TIM3_Init(void);
static void MX_USART1_UART_Init(void);
/* USER CODE BEGIN PFP */
/* USER CODE END PFP */
/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */
uint8_t CNBR, VNBR, DILE;
float CNBR_fee, VNBR_fee;
uint8_t mode;
uint8_t Got_Car;
Car_type Car_info[8];
Car_type Now_Car;
uint8_t arr[40];
/* USER CODE END 0 */
/**
* @brief The application entry point.
* @retval int
*/
int main(void)
{
/* USER CODE BEGIN 1 */
uint8_t key, Save, i;
uint8_t ass[40];
/* USER CODE END 1 */
/* MCU Configuration--------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* USER CODE BEGIN Init */
/* USER CODE END Init */
/* Configure the system clock */
SystemClock_Config();
/* USER CODE BEGIN SysInit */
/* USER CODE END SysInit */
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_TIM3_Init();
MX_USART1_UART_Init();
/* USER CODE BEGIN 2 */
HAL_TIM_PWM_Start(&htim3,TIM_CHANNEL_2);
TIM3->CCR2 = 0;
LCD_Init();
LCD_Clear(Black);
LCD_SetBackColor(Black);
LCD_SetTextColor(White);
GPIOC->ODR |= 0xff00;
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_2,GPIO_PIN_SET);
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_2,GPIO_PIN_RESET);
key = 0;
Save = 0;
CNBR_fee = 3.5;
VNBR_fee = 2.0;
CNBR = VNBR = 0;
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
Display();
key = KEY_Scan();
if(key) KEY_Handle(key);
HAL_UART_Receive_IT(&huart1,arr,24);
DILE = 8-CNBR-VNBR;
if(Got_Car)//收到车辆信息
{
Got_Car = 0;
Save = Confirm();
if(Save)
{
for(i = 0; i < 8; i++)
{
if(Car_info[i].NBR == Now_Car.NBR && strcmp((char *)Car_info[i].Name,(char *)Now_Car.Name) == 0)
{
Save = 0;
Output_A_Car(i);
break;
}
}
if(Save)
{
for(i = 0; i < 8; i++)
{
if(Car_info[i].NBR != 'C' && Car_info[i].NBR != 'V')
{
Save = 0;
Input_A_Car(i);
break;
}
}
}
}
else
{
sprintf((char *)ass,"ERROR");
HAL_UART_Transmit(&huart1, ass, sizeof(ass), 50);
}
}
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
/* LD1亮 */
if(DILE>0)
HAL_GPIO_WritePin(GPIOC, GPIO_PIN_8, GPIO_PIN_RESET);
else
HAL_GPIO_WritePin(GPIOC, GPIO_PIN_8, GPIO_PIN_SET);
GPIOC->ODR |= 0xfe00;
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_2,GPIO_PIN_SET);
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_2,GPIO_PIN_RESET);
}
/* USER CODE END 3 */
}
/**
* @brief System Clock Configuration
* @retval None
*/
void SystemClock_Config(void)
{
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
/** Configure the main internal regulator output voltage
*/
HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
/** Initializes the RCC Oscillators according to the specified parameters
* in the RCC_OscInitTypeDef structure.
*/
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV2;
RCC_OscInitStruct.PLL.PLLN = 20;
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV2;
RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV2;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
{
Error_Handler();
}
/** Initializes the CPU, AHB and APB buses clocks
*/
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
{
Error_Handler();
}
/** Initializes the peripherals clocks
*/
PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART1;
PeriphClkInit.Usart1ClockSelection = RCC_USART1CLKSOURCE_PCLK2;
if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
{
Error_Handler();
}
}
/**
* @brief TIM3 Initialization Function
* @param None
* @retval None
*/
static void MX_TIM3_Init(void)
{
/* USER CODE BEGIN TIM3_Init 0 */
/* USER CODE END TIM3_Init 0 */
TIM_ClockConfigTypeDef sClockSourceConfig = {0};
TIM_MasterConfigTypeDef sMasterConfig = {0};
TIM_OC_InitTypeDef sConfigOC = {0};
/* USER CODE BEGIN TIM3_Init 1 */
/* USER CODE END TIM3_Init 1 */
htim3.Instance = TIM3;
htim3.Init.Prescaler = 80-1;
htim3.Init.CounterMode = TIM_COUNTERMODE_UP;
htim3.Init.Period = 499;
htim3.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
htim3.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
if (HAL_TIM_Base_Init(&htim3) != HAL_OK)
{
Error_Handler();
}
sClockSourceConfig.ClockSource = TIM_CLOCKSOURCE_INTERNAL;
if (HAL_TIM_ConfigClockSource(&htim3, &sClockSourceConfig) != HAL_OK)
{
Error_Handler();
}
if (HAL_TIM_PWM_Init(&htim3) != HAL_OK)
{
Error_Handler();
}
sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;
sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
if (HAL_TIMEx_MasterConfigSynchronization(&htim3, &sMasterConfig) != HAL_OK)
{
Error_Handler();
}
sConfigOC.OCMode = TIM_OCMODE_PWM1;
sConfigOC.Pulse = 0;
sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
if (HAL_TIM_PWM_ConfigChannel(&htim3, &sConfigOC, TIM_CHANNEL_2) != HAL_OK)
{
Error_Handler();
}
/* USER CODE BEGIN TIM3_Init 2 */
/* USER CODE END TIM3_Init 2 */
HAL_TIM_MspPostInit(&htim3);
}
/**
* @brief USART1 Initialization Function
* @param None
* @retval None
*/
static void MX_USART1_UART_Init(void)
{
/* USER CODE BEGIN USART1_Init 0 */
/* USER CODE END USART1_Init 0 */
/* USER CODE BEGIN USART1_Init 1 */
/* USER CODE END USART1_Init 1 */
huart1.Instance = USART1;
huart1.Init.BaudRate = 9600;
huart1.Init.WordLength = UART_WORDLENGTH_8B;
huart1.Init.StopBits = UART_STOPBITS_1;
huart1.Init.Parity = UART_PARITY_NONE;
huart1.Init.Mode = UART_MODE_TX_RX;
huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
huart1.Init.OverSampling = UART_OVERSAMPLING_16;
huart1.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
huart1.Init.ClockPrescaler = UART_PRESCALER_DIV1;
huart1.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
if (HAL_UART_Init(&huart1) != HAL_OK)
{
Error_Handler();
}
if (HAL_UARTEx_SetTxFifoThreshold(&huart1, UART_TXFIFO_THRESHOLD_1_8) != HAL_OK)
{
Error_Handler();
}
if (HAL_UARTEx_SetRxFifoThreshold(&huart1, UART_RXFIFO_THRESHOLD_1_8) != HAL_OK)
{
Error_Handler();
}
if (HAL_UARTEx_DisableFifoMode(&huart1) != HAL_OK)
{
Error_Handler();
}
/* USER CODE BEGIN USART1_Init 2 */
/* USER CODE END USART1_Init 2 */
}
/**
* @brief GPIO Initialization Function
* @param None
* @retval None
*/
static void MX_GPIO_Init(void)
{
GPIO_InitTypeDef GPIO_InitStruct = {0};
/* GPIO Ports Clock Enable */
__HAL_RCC_GPIOC_CLK_ENABLE();
__HAL_RCC_GPIOF_CLK_ENABLE();
__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOB_CLK_ENABLE();
__HAL_RCC_GPIOD_CLK_ENABLE();
/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOC, GPIO_PIN_13|GPIO_PIN_14|GPIO_PIN_15|GPIO_PIN_0
|GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_4
|GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7|GPIO_PIN_8
|GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_12, GPIO_PIN_RESET);
/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOA, GPIO_PIN_8, GPIO_PIN_RESET);
/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOD, GPIO_PIN_2, GPIO_PIN_RESET);
/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_5|GPIO_PIN_8|GPIO_PIN_9, GPIO_PIN_RESET);
/*Configure GPIO pins : PC13 PC14 PC15 PC0
PC1 PC2 PC3 PC4
PC5 PC6 PC7 PC8
PC9 PC10 PC11 PC12 */
GPIO_InitStruct.Pin = GPIO_PIN_13|GPIO_PIN_14|GPIO_PIN_15|GPIO_PIN_0
|GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_4
|GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7|GPIO_PIN_8
|GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_12;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/*Configure GPIO pin : PA0 */
GPIO_InitStruct.Pin = GPIO_PIN_0;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/*Configure GPIO pins : PB0 PB1 PB2 */
GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/*Configure GPIO pin : PA8 */
GPIO_InitStruct.Pin = GPIO_PIN_8;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/*Configure GPIO pin : PD2 */
GPIO_InitStruct.Pin = GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
/*Configure GPIO pins : PB5 PB8 PB9 */
GPIO_InitStruct.Pin = GPIO_PIN_5|GPIO_PIN_8|GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
}
/* USER CODE BEGIN 4 */
/* USER CODE END 4 */
/**
* @brief This function is executed in case of error occurrence.
* @retval None
*/
void Error_Handler(void)
{
/* USER CODE BEGIN Error_Handler_Debug */
/* User can add his own implementation to report the HAL error return state */
__disable_irq();
while (1)
{
}
/* USER CODE END Error_Handler_Debug */
}
#ifdef USE_FULL_ASSERT
/**
* @brief Reports the name of the source file and the source line number
* where the assert_param error has occurred.
* @param file: pointer to the source file name
* @param line: assert_param error line source number
* @retval None
*/
void assert_failed(uint8_t *file, uint32_t line)
{
/* USER CODE BEGIN 6 */
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
.c
#include "function.h"
#include "stdio.h"
#include "lcd.h"
#include "string.h"
uint8_t str[40];
uint8_t Month[] = {0,31,28,31,30,31,30,31,31,30,31,30,31};
uint8_t app[40];
void Display(void)
{
if(mode == 0)
{
sprintf((char *)str," Para");
LCD_DisplayStringLine(Line2,str);
sprintf((char *)str," CNBR:%d",CNBR);
LCD_DisplayStringLine(Line4,str);
sprintf((char *)str," VNBR:%d",VNBR);
LCD_DisplayStringLine(Line6,str);
sprintf((char *)str," DILE:%d",DILE);
LCD_DisplayStringLine(Line8,str);
}
else if(mode == 1)
{
sprintf((char *)str," Data");
LCD_DisplayStringLine(Line2,str);
sprintf((char *)str," CNBR:%.2f",CNBR_fee);
LCD_DisplayStringLine(Line4,str);
sprintf((char *)str," VNBR:%.2f",VNBR_fee);
LCD_DisplayStringLine(Line6,str);
}
}
uint8_t KEY_Scan(void)
{
static uint8_t flag=1;//单独按键，防止连按
if(flag &&(KEY_B1 == 0 || KEY_B2 == 0 || KEY_B3 == 0 || KEY_B4== 0 ))
{
HAL_Delay(10);//消抖
flag = 0;
if (KEY_B1 == 0) return B1_Press;
else if (KEY_B2 == 0) return B2_Press;
else if (KEY_B3 == 0) return B3_Press;
else if (KEY_B4 == 0) return B4_Press;
}else if(KEY_B1 == KEY_B2 == KEY_B3 == KEY_B4 == 1) flag = 1;
return 0;
}
void KEY_Handle(uint8_t key)
{
static uint8_t output = 0;
if(key == B1_Press)
{
mode = !mode;
LCD_Clear(Black);
}
else if(key == B2_Press && mode == 1)
{
CNBR_fee += 0.5f;
VNBR_fee += 0.5f;
}
else if(key == B3_Press && mode == 1)
{
CNBR_fee -= 0.5f;
VNBR_fee -= 0.5f;
}
else if(key == B4_Press)
{
output = !output;
if(output)
TIM3->CCR2 = 100;
else
TIM3->CCR2 = 0;
}
}
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart)//中断时间有要求所以不做过多处理
{
/*
CNBR:B001: 2 0 0 4 1 8 0 9 0 0 0 0
0123456789 10 11 12 13 14 15 16 17 18 19 20 21 22
*/
Now_Car.NBR = arr[0];
Now_Car.Name[0] = arr[5];
Now_Car.Name[1] = arr[6];
Now_Car.Name[2] = arr[7];
Now_Car.Name[3] = arr[8];
Now_Car.Year = (arr[10]-'0')*10+(arr[11]-'0');
Now_Car.Month = (arr[12]-'0')*10+(arr[13]-'0');
Now_Car.Day = (arr[14]-'0')*10+(arr[15]-'0');
Now_Car.Hour = (arr[16]-'0')*10+(arr[17]-'0');
Now_Car.Minute = (arr[18]-'0')*10+(arr[19]-'0');
Now_Car.Second = (arr[20]-'0')*10+(arr[21]-'0');
Got_Car = 1;
memset(arr,0,sizeof(arr));
}
uint8_t Confirm(void)
{
uint16_t Year;
if((Now_Car.NBR == 'C' || Now_Car.NBR == 'V') && Now_Car.Second < 60 && Now_Car.Minute < 60 && Now_Car.Hour < 23)
{
Year = 2000 + Now_Car.Year;
if(Now_Car.Month == 1 || Now_Car.Month == 3 || Now_Car.Month == 5 || Now_Car.Month == 7 || Now_Car.Month == 8 || Now_Car.Month == 10 || Now_Car.Month == 12)//如果月份1、3、5、7、8、10、12，天数小于32
{
if(Now_Car.Day > 31)
return 0;
}
else if(Now_Car.Month == 4 || Now_Car.Month == 6 || Now_Car.Month == 9 || Now_Car.Month == 11)//如果月份4、6、9、11，天数小于31
{
if(Now_Car.Day > 30)
return 0;
}
else if(Year % 400 == 0 || (Year % 4 == 0 && Year % 100 != 0))//判断年份是闰年
{
if(Now_Car.Day > 28)
return 0;
}
else
{
if(Now_Car.Day > 29)
return 0;
}
return 1;
}
else
return 0;
}
void Output_A_Car(uint8_t location)
{
float fee = 0;
uint16_t i;
uint32_t Second, Second_aim;
uint8_t time;
/* 以2000开始，计算从2000到该时间过的秒 */
for(i = 2000; i < 2000+Car_info[location].Year ; i++)
{
if(i % 400 == 0 || (i % 4 == 0 && i % 100 != 0))//判断年份是闰年
{
Second += 366*24*60*60;
}
else
Second += 365*24*60*60;
}
for(i = 1; i < Car_info[location].Month ; i++)
{
Second += Month[i];
if(i % 400 == 0 || (i % 4 == 0 && i % 100 != 0))//判断年份是闰年
{
Second++;
}
}
for(i = 1; i < Car_info[location].Day; i++)
{
Second += 24*60*60;
}
for(i = 1; i < Car_info[location].Hour; i++)
{
Second += 60*60;
}
for(i = 1; i < Car_info[location].Minute; i++)
{
Second += 60;
}
Second += Car_info[location].Second;
/* Second_aim */
for(i = 2000; i < 2000+Now_Car.Year ; i++)
{
if(i % 400 == 0 || (i % 4 == 0 && i % 100 != 0))//判断年份是闰年
{
Second_aim += 366*24*60*60;
}
else
Second_aim += 365*24*60*60;
}
for(i = 1; i < Now_Car.Month ; i++)
{
Second_aim += Month[i];
if(i % 400 == 0 || (i % 4 == 0 && i % 100 != 0))//判断年份是闰年
{
Second_aim++;
}
}
for(i = 1; i < Now_Car.Day; i++)
{
Second_aim += 24*60*60;
}
for(i = 1; i < Now_Car.Hour; i++)
{
Second_aim += 60*60;
}
for(i = 1; i < Now_Car.Minute; i++)
{
Second_aim += 60;
}
Second_aim += Now_Car.Second;
/* 秒数抓化成小时 */
time = (uint8_t)(Second_aim - Second)/60/60;
if((Second_aim - Second) > time*60*60)
{
time++;//余数补偿
}
// sprintf((char *)app,"%.2d%.2d%.2d%.2d%.2d%.2d%d\r\n",Car_info[location].Year, Car_info[location].Month,Car_info[location].Day
// ,Car_info[location].Hour,Car_info[location].Minute,Car_info[location].Second,Second);
// HAL_UART_Transmit(&huart1, app, sizeof(app), 200);
// sprintf((char *)app,"%.2d%.2d%.2d%.2d%.2d%.2d%d\r\n",Now_Car.Year, Now_Car.Month,Now_Car.Day
// ,Now_Car.Hour,Now_Car.Minute,Now_Car.Second,Second_aim);
// HAL_UART_Transmit(&huart1, app, sizeof(app), 200);
/* 计算费用 */
if(Now_Car.NBR == 'C')
{
fee = time*CNBR_fee;
CNBR--;
}
else
{
fee = time*VNBR_fee;
VNBR--;
}
sprintf((char *)app,"%cNBR:%.2d:%3.2f",Car_info[location].NBR,time,fee);
HAL_UART_Transmit(&huart1, app, sizeof(app), 0xfff);
/* 清除车辆信息 */
Car_info[location].NBR = '\0';
memset(Car_info[location].Name,0,sizeof(Car_info[location].Name));
Car_info[location].Year = 0;
Car_info[location].Month = 0;
Car_info[location].Day = 0;
Car_info[location].Hour = 0;
Car_info[location].Minute = 0;
Car_info[location].Second = 0;
}
void Input_A_Car(uint8_t location)
{
if(Now_Car.NBR == 'C')
CNBR++;
else
VNBR++;
Car_info[location].NBR = Now_Car.NBR;
strcpy((char *)Car_info[location].Name, (char *)Now_Car.Name);
Car_info[location].Year = Now_Car.Year;
Car_info[location].Month = Now_Car.Month;
Car_info[location].Day = Now_Car.Day;
Car_info[location].Hour = Now_Car.Hour;
Car_info[location].Minute = Now_Car.Minute;
Car_info[location].Second = Now_Car.Second;
}
.h
#ifndef __function_h
#define __function_h
#include "main.h"
#define KEY_B1 HAL_GPIO_ReadPin(GPIOB,GPIO_PIN_0)
#define KEY_B2 HAL_GPIO_ReadPin(GPIOB,GPIO_PIN_1)
#define KEY_B3 HAL_GPIO_ReadPin(GPIOB,GPIO_PIN_2)
#define KEY_B4 HAL_GPIO_ReadPin(GPIOA,GPIO_PIN_0)
#define B1_Press 1
#define B2_Press 2
#define B3_Press 3
#define B4_Press 4
typedef struct{
char NBR;
uint8_t Name[4];
uint8_t Year;
uint8_t Month;
uint8_t Day;
uint8_t Hour;
uint8_t Minute;
uint8_t Second;
}Car_type;
extern uint8_t CNBR, VNBR ,DILE;
extern float CNBR_fee, VNBR_fee;
extern uint8_t mode;
extern uint8_t Got_Car;
extern Car_type Car_info[8];
extern Car_type Now_Car;
extern uint8_t arr[40];
extern UART_HandleTypeDef huart1;
void Display(void);
uint8_t KEY_Scan(void);
void KEY_Handle(uint8_t key);
uint8_t Confirm(void);
void Output_A_Car(uint8_t location);
void Input_A_Car(uint8_t location);
#endif
【排序算法】之lowb三人组冒泡、插入、选择 什么是lowb三人组 冒泡排序bubble so...
歌词编辑器 歌词编辑器 第一步：选择要播放的歌曲并播放 第二步：填写全部的歌词...
vbs:把一段文字中指定字符颜色变成红色的正则 functionc(Tstr,Word) Dimre Setre...
一、正则表达式概述 二、正则表达式在VBScript中的应用 三、正则表达式在VavaScr...
前言 相信大家都知道在IDE中代码的智能提示几乎都是标配，虽然一些文本编辑器也...
微信文件传输助手是微信电脑版与手机微信之间相互传输图片等文件的好工具，但很...
本文将研究 ES6 的 for ... of 循环。 旧方法 在过去，有两种方法可以遍历 javas...
计算属性computed： 支持缓存，只有依赖数据发生改变，才会重新进行计算 不支持...
一石激起千层浪，继中国区浩浩荡荡的大裁员告一段落之后，甲骨文并未因此收起手...
ADO对象： Connection Command Recordset Record Stream ASP支持的对象很多，可...
